Cart
Articles 0
Products for the sum 0 PLN
Delivery
Total
Show checkout

STS.Electro Case Study: Repair of a KIA Optima Hybrid Electric Motor

Car
KIA Optima

Problem

After a sudden acceleration, the hybrid car lost power, and the internal combustion engine stalled when the gear was engaged. Diagnostics revealed that the 12V battery was not charging and that there were numerous errors.

Result

The automatic transmission was removed and the built-in high-voltage electric motor was inspected; an electrical breakdown between the phase buses and the housing was isolated; and the stator was professionally rewound to restore the dielectric strength of the winding.

Fault codes
P0A78, P0AA6
Mileage
300,000 km
Error codes
P0A78, P0AA6
Usage
Taxi
Insulation after repair
> 1000 MΩ
STS.Electro Case Study: Repair of a KIA Optima Hybrid Electric Motor

A challenge for specialists: a high-mileage KIA Optima hybrid transmission

Cars used as taxis are subjected to extreme loads: constant urban stop-start driving, high daily mileage, temperature swings and little time for preventive maintenance. When the owner of a KIA Optima TF 2.0 MPI Hybrid with 300,000 km came to our service centre in Warsaw, a standard scan of the error codes was not enough — the case required in-depth engineering analysis.

Design anatomy

In first- and second-generation Korean hybrids (KIA Optima / Hyundai Sonata), a three-phase traction motor is installed instead of a torque converter between the 2-litre petrol engine and the 6-speed automatic transmission. Inside it is a multi-plate “hybrid” clutch that connects or disconnects the combustion engine depending on the driving mode.

A shared oil circuit: the ATF bathes both the mechanical gears and clutches and the windings of the high-voltage motor.

How the fault developed

  1. Build-up of wear particles. At high mileage the ATF accumulates a high concentration of fine dust from the clutch friction plates.
  2. Loss of dielectric properties. Contaminated oil stops being an insulator: settling on the stator and plastic insulators, it forms a conductive deposit.
  3. The critical moment — breakdown. During hard overtaking the power electronics fed maximum current to the motor. The winding heated up instantly, and where the insulation had been weakened by deposits and micro-cracks, a high-voltage arc formed.

Step-by-step workflow

5 steps, from removing the gearbox to reassembly. Click a photo to view it in full.

  1. Step 1 of 5

    Removal and diagnostics of the transmission

    Initial measurements and an insulation-tester check of the power circuit confirmed current leakage and insulation breakdown directly on the car. The unit was removed and dismantled on a dedicated bench for detailed diagnostics.

  2. Step 2 of 5

    Analysis and location of the phase busbar breakdown

    Technical detail: the stator windings are fed through three massive copper busbars moulded into a heat-resistant plastic insulating block.

    What we found: the high-voltage arc burned through the plastic insulator between the busbars. Burnt oil and plastic turned into carbon — a perfect conductor.

    Such damage cannot be filled with epoxy without completely removing the carbon deposits: hot oil and vibration quickly break the resin down, and the fix only lasts a few kilometres.

  3. Step 3 of 5

    Stator inspection and “floating” inter-turn short circuits

    Technical detail: sections of the stator winding show the characteristic local darkening of the enamel varnish.

    What we found: overheating destroyed the integrity of the enamel insulation. A “floating” short to ground developed: when cold the resistance is within spec, but when hot the expanded copper touches the steel core and the system shuts down instantly.

  4. Step 4 of 5

    Complete rewinding and restoration of the stator

    Partial repair of a high-voltage motor winding (above 270 V) is unacceptable for safety and reliability reasons.

    • The old winding was completely removed and the stator cleaned of insulation residue and combustion products.
    • New high-temperature enamelled wire was laid with new slot insulators, followed by repeated impregnation with dielectric varnish and oven curing.
  5. Step 5 of 5

    Rotor, hybrid clutch and preparation for assembly

    • The rotor and the inner clutch drum were flushed of the metal dust suspension.
    • The hybrid clutch friction plates were inspected; oil seals and sealing rings were replaced.
    • Final measurements: insulation resistance returned to factory values — over 1000 MΩ.

Repair results

  • Codes P0A78 and P0AA6 were completely cleared from the HCU memory.
  • The DC/DC converter works correctly — the 12 V battery charges steadily.
  • The engine starts smoothly and switches between electric and hybrid modes without delay.

Why timely transmission service on a hybrid is “insurance” against an expensive repair

This case clearly shows that the oil in a hybrid transmission is not just a lubricant but an insulator for the high-voltage system. If it is not changed on time, accumulated metal and friction dust turn the oil into a conductor, the temperature inside the motor rises and the winding insulation breaks down — all the way to a short circuit and a stranded car.

Regular transmission service costs many times less than removing the gearbox, dismantling the unit and rewinding the motor.

Noticed jerks when the engine starts, unusual noise or system errors?

Don't wait until contaminated oil causes a breakdown on the road or kills the inverter. STS.Electro in Warsaw will run a computer diagnosis of the hybrid system and measure insulation resistance with a high-voltage insulation tester.

Other cases

Subscribe to news!